Просмотр кода страницы Admins:MegaCli команды

=Команды MegaCli=

MegaCli лежит в /opt/lsi/MegaCli/

* flash bios
::MegaCli -adpfwflash -f /scripts/firmware/lsi_imr_fw.rom -aALL
::MegaCli -adpfwflash -f imr_fw.rom -NoVerChk -aAll
::MegaCli -adpfacdefset -aALL # reset to factory default

*controller info
::MegaCli -AdpAllinfo -aALL
::MegaCli -PDGetNum -a0 # nubmer of discs
::MegaCli -PDInfo -PhysDrv [64:0] -aALL
::MegaCli -PDMakeJBOD -PhysDrv[64:4]

*clear controller config to defaults
::MegaCli -CfgClr -aALL

*delete all
::MegaCli -CfgLdDel -LALL -aALL

*create raid
::MegaCli -CfgLdAdd -r5 [64:0, 64:1, 64:2, 64:3] -a0
::MegaCli -CfgLdAdd -r0 [64:4,64:5,64:6,64:7] -a0

*get free devices
::MegaCli -PDList -a0 | grep -e '^Enclosure Device ID:' -e '^Slot Number:'

*get raid info
::MegaCli -LDInfo -Lall -aALL
::MegaCli -PDMakeGood -PhysDrv[64:4] -force -aALL > /dev/null
::MegaCli -PDMakeGood -PhysDrv[64:5] -force -aALL > /dev/null
::MegaCli -PDMakeGood -PhysDrv[64:6] -force -aALL > /dev/null
::MegaCli -PDMakeGood -PhysDrv[64:7] -force -aALL > /dev/null
::MegaCli -PDMakeJBOD -PhysDrv[64:4,64:5,64:6,64:7] -a0
::MegaCli -CfgLdAdd -r0 [64:4,64:5,64:6,64:7] -a0
::MegaCli -AdpEventLog -GetEvents -f logfile -aALL # Dump all events from the adapters event log to a file named logfile
::MegaCli -PDList -aAll # Dump information about all Phsyical Disks
::MegaCli -LDInfo -LAll -aAll # Dump information about all Logical Disks on all adapters
::MegaCli -LdPdInfo -aAll # Dump information of all logical and physical disks on all known adapters
::MegaCli -AdpSetProp -EnableJBOD 1 -aALL
::MegaCli -CfgDsply -aAll

*adapter diagnostic
::MegaCli -AdpDiag -a0

*Controller information
::MegaCli -AdpAllInfo -aALL
::MegaCli -CfgDsply -aALL
::MegaCli -AdpEventLog -GetEvents -f events.log -aALL && cat events.log

*Enclosure information
::MegaCli -EncInfo -aALL

*Virtual drive information
::MegaCli -LDInfo -Lall -aALL

*Physical drive information
::MegaCli -PDList -aALL
::MegaCli -PDInfo -PhysDrv [E:S] -aALL

*Battery backup information
::MegaCli -AdpBbuCmd -aALL

=Controller management=

*Silence active alarm
::MegaCli -AdpSetProp AlarmSilence -aALL

*Disable alarm
::MegaCli -AdpSetProp AlarmDsbl -aALL

*Enable alarm
::MegaCli -AdpSetProp AlarmEnbl -aALL

*Physical drive management

*Set state to offline
::MegaCli -PDOffline -PhysDrv [E:S] -aN

*Set state to online
::MegaCli -PDOnline -PhysDrv [E:S] -aN

*Mark as missing
::MegaCli -PDMarkMissing -PhysDrv [E:S] -aN

*Prepare for removal
::MegaCli -PdPrpRmv -PhysDrv [E:S] -aN

*Replace missing drive
::MegaCli -PdReplaceMissing -PhysDrv [E:S] -ArrayN -rowN -aN

*Rebuild drive
::MegaCli -PDRbld -Start -PhysDrv [E:S] -aN
::MegaCli -PDRbld -Stop -PhysDrv [E:S] -aN
::MegaCli -PDRbld -ShowProg -PhysDrv [E:S] -aN

*Clear drive
::MegaCli -PDClear -Start -PhysDrv [E:S] -aN
::MegaCli -PDClear -Stop -PhysDrv [E:S] -aN
::MegaCli -PDClear -ShowProg -PhysDrv [E:S] -aN

*MegaCli -PDMakeGood -PhysDrv[E:S] -aN
::This changes drive in state Unconfigured-Bad to Unconfigured-Good.

*Set the drive offline, if it is not already offline due to an error
::MegaCli -PDOffline -PhysDrv [E:S] -aN

*Mark the drive as missing
::MegaCli -PDMarkMissing -PhysDrv [E:S] -aN

*Prepare drive for removal
::MegaCli -PDPrpRmv -PhysDrv [E:S] -aN

*If you’re using hot spares then the replaced drive should become your new hot spare drive:
::MegaCli -PDHSP -Set -PhysDrv [E:S] -aN

*In case you’re not working with hot spares, you must re-add the new drive to your RAID virtual drive and start the rebuilding
::MegaCli -PdReplaceMissing -PhysDrv [E:S] -ArrayN -rowN -aN
::MegaCli -PDRbld -Start -PhysDrv [E:S] -aN
::MegaCli -CfgLdAdd -r0 [0:1, 0:1] -a0
::MegaCli -LDInfo -Lall -aALL

*View all controleler informations
::MegaCli -AdpAllInfo -aAll
::MegaCli -LDSetProp CachedBadBBU -LALL -aALL

*Delete all devices
::MegaCli -CfgLdDel -LALL -aALL
::MegaCli -CfgLdAdd -r1 [252:0,252:1] -a0
::MegaCli -CfgLdAdd -r10 [252:0,252:1,252:2,252:3] -a0

*create RAID5
::MegaCli -CfgLdAdd -r5 [64:0,64:1,64:2,64:3] -a0

*create RAID10
::MegaCli -CfgSpanAdd -r10 -Array0[64:0,64:1] -Array1[64:2,64:3] -a0

*create RAID10
::MegaCli -AdpSetProp -EnableJBOD 1

*Enable disks cache
::MegaCli -LDSetProp EnDskCache -LAll -aAll

*Force flash
::MegaCli -adpfwflash -f ./12.12.0-0111.rom -NoVerChk -a0

*load controller defauts
::MegaCli -adpfacdefset -aALL